Mac Users Of Mtc (apple: Go Ahead, Take A Bite!)

[irvin1130]

guys can you help me set up my airport express,my airport express cant detect my Linksys WRT54G to make an extended signal

[chunkyhunk]

guys can you help me set up my airport express,my airport express cant detect my Linksys WRT54G to make an extended signal

 

Have you tried interchanging your APX with the Linksys, and using the APX as the "repeater" instead?

 

Also, does you Mac have a built-in Airport to begin with? Mind listing down your setup?

[boomouse]

guys can you help me set up my airport express,my airport express cant detect my Linksys WRT54G to make an extended signal

 

Intructions on how to extend a Linksys WRT54G network via AirPort Express can be found here:

 

http://www.macosxhints.com/article.php?story=20060609053254368

 

I will save you the trouble of following the link because I have been asked this several times so, for the benefit of other thread readers, here it is:

 

In order to add an AX to your existing Linksys WRT54G wireless network you should first take the following precautions:

 

1. Disable or remove all firewalls on the computer on which you will be configuring the network. You should be able to re-establish your previous computer configuration after the network is set-up.

2. You must be running at least Version 4.1 of the AirPort Software. Make sure all of you system software is up-to-date by running Software Update found in your Apple Menu. Repair Permissions both before and after updating your software.

3. Perform a Factory Default Reset of the AX.

4. Immediately before performing the configuration process, Restart the computer on which you will be performing the configuration. Ideally, you will also shut down any other devices connected to the wireless network, but you probably will be able to configure the network without doing so.

5. Each step of the configuration process must be closely followed. Skip no steps, and perform no shortcuts.

 

Read on for the step-by-Step instructions.

 

Ready the Linksys WRT54G

 

1. Log into your Linksys WRT54G administration web page. In a new browser window, type the router address (http://192.168.1.1. This step (and the following steps) assume that you have not changed the default router address. If you have changed it from the default, then use the address you have assigned. The default administration password is admin.

2. Check the Firmware version of the router. You must be running Version level 3.01.3. The latest Linksys WRT54G Firmware can be found on Linksys' download page.

3. If you need to update your router firmware, detailed instructions for updating can be found in the Users Guide, which essentially instructs you to open the Administration tab from your Linksys configuration page, choose the Firmware Upgrade option, and following the on-screen instructions. If you need to update your firmware, make sure you restart the router.

4. While logged into the updated router using the instructions above, record the following information, which is found in the Wireless/Basic Wireless Settings:

* Wireless Channel pulldown menu - make sure channel 11 is selected

* SSID - (ie your network name), capitalization counts)

* WEP Password (choose 128 bit, type in a passphrase, key the "Generate" button, and write down use the hexadecimal equivalent generated as Key 1)

* Status Tab (make sure Wireless is selected) and record the MAC address listed here

 

Configuring the AirPort Express

 

1. If you have not already performed a Factory Default Reset of the AX, do so now. This is accomplished very simply by holding in the reset button on your AirPort Express while plugging it in. Continue to hold the reset button until you see the yellow light flash green four times. This may take longer than the time recommended in the referenced instructions. Release the Reset Button and allow the unit a few seconds to cycle.

2. Connect the AirPort Express to your a Linksys WRT54G LAN port using a CAT5 ethernet cable.

3. Launch the AirPort Admin Utility (not the AirPort Set-up Assistant) located in the Utilities Folder in the Applications Folder on your computer hard drive. The AirPort Admin Utility should list the Default Address name of the AX you are adding to your network to extend the range of the network using WDS. Select the AX. The status light on the AX should flash.

4. Click Configure, and choose the AirPort tab on the new window. Under the Base Station heading chose a name. This name will show up in the 'Select Base Station' window once your configuration is complete. Contact and Location are optional, and may be left blank.

5. Under the Airport Network heading's pulldown menu choose 'Create a Wireless Network (Home Router).' In the Name field, enter the SSID you copied down per the above instructions (enter it exactly, or you will create a separate network).

6. Click on Change Wireless Security. Select 128 bit WEP in the pulldown menu. Under Network Password, you're going to type in the Key 1 hexadecimal password proceeded by a dollar sign ($). Re-enter the hexadecimal password in the Verify box.

7. Change to Channel 11.

8. Under the Internet Tab in the pulldown menu Connect Using, Choose AirPort (WDS).

9. In the MAC Address window, type in the number you recorded, as instructed above.

10. Select 'Also Allow Wireless Client Computers.'

11. Now, under Configure, you have a choice. Either select "Using DHCP, or Manually. Many people have had success using the DHCP option, however, a manual configuration is often used to overcome some networking anomalies. If you choose Manually, use the following information to configure the AX:

* IP Address: 192.168.1.2

* Subnet mask: 255.255.255.0

* Router Address: 192.168.1.1

12. Under the Network tab, deselect Distribute IP addresses.

13. Under the WDS tab, check 'Enable this Base Station as a WDS.' In the pulldown menu, select 'Remote Base Station.' Also select 'Allow Wireless Clients on this Base Station.' If all is working as expected, the Main AirPort ID box should automatically display the MAC number you entered in step five.

14. Under the Music tab, if you'd like, select 'Enable AirTunes on this Base Station.' Under 'iTunes Speaker Name,' enter a name for your remote speakers. This name will show up in an iTunes pulldown menu once your configuration is complete.

15. Click Update and load your new configuration into your AX.

16. When the AX recycles, disconnect the ethernet cable between the WRT54G and the AX. Unplug your AX from the power, and move it to the remote location you have selected for extending your network. Plug it in to a wall outlet and after the AX resets it should display a solid Green light.

 

If you're using your extended network to distribute iTunes to remote speakers there are two additional steps to perform.

 

1. You'll need to use an adapter cable to feed the mini jack out on your AX into your stereo or powered speakers. Launch iTunes and look in the lower right of the resulting window.

2. There should now be a pulldown menu that offers you a choice of music destinations, either Computer, or the name you entered for your remote speakers. Select the remote speakers, and iTunes should stream to those speakers.

Edited July 27, 2008 by boomouse

[shadowspy]

finally got my new macbook intel 2.4 ghz...panalo kahit 2 gb lang ram...might buy another 2 gb once i get back

 

just a question...bakit madalas mag crash ang YM sa mac....pansin ko lang

[chunkyhunk]

finally got my new macbook intel 2.4 ghz...panalo kahit 2 gb lang ram...might buy another 2 gb once i get back

 

just a question...bakit madalas mag crash ang YM sa mac....pansin ko lang

 

Have you updated to the latest version?

[shadowspy]

Have you updated to the latest version?

 

 

yup...I just downloaded the most recent version...it also happens to a mac g4 that i borrowed for a few months

[chunkyhunk]

yup...I just downloaded the most recent version...it also happens to a mac g4 that i borrowed for a few months

 

Now that is strange. I think it may have something to do with legacy preferences in your system, but that's a longshot. Try uninstalling YM and all it's components using third party cleaners (Like spring cleaning and appzapper, both are shareware) that deletes all application-related files.

 

Try getting adiumX at http://adiumx.com for the meantime if you're not too particular with the messenger platform. You won't have the usual features like webcam, voice chat and file transfers (transfers, I think are limited to adium to adium users) but it'll at least allow you to chat freely.

[shadowspy]

Now that is strange. I think it may have something to do with legacy preferences in your system, but that's a longshot. Try uninstalling YM and all it's components using third party cleaners (Like spring cleaning and appzapper, both are shareware) that deletes all application-related files.

 

Try getting adiumX at http://adiumx.com for the meantime if you're not too particular with the messenger platform. You won't have the usual features like webcam, voice chat and file transfers (transfers, I think are limited to adium to adium users) but it'll at least allow you to chat freely.

 

yup weird talaga kasi I installed it on a brand new macbook. so walang kahit ano other than OSX. second program i installed after firefox.

[Duckie4120]

finally got my new macbook intel 2.4 ghz...panalo kahit 2 gb lang ram...might buy another 2 gb once i get back

 

just a question...bakit madalas mag crash ang YM sa mac....pansin ko lang

 

Same thing happens to me.

[chunkyhunk]

Did a little bit of googling. Try installing the lastest Flash player.

[libraprime]

Hello! Pwede po bang magsingit ng commercial? I posted a similar message in the linux folder.

 

I work for a company which provides ICT education packages. I'm looking for someone who can write a book on the MAC OS targeted for high school/tertiary level students. If anyone is interested, please email me your CV and sample syllabus at libraprime@gmail.com.

 

Thanks and more power!

[boomouse]

APPLE SECURITY UPDATE 2008-005 FIXES DNS ISSUE

Apple rolled out a late day security update on Thursday

that addressed potential DNS-related flaws in Mac OS X

Leopard and Tiger. Security Update 2008-005 prevents

malicious attackers from forging Web sites -- a trick that

could potentially be used for phishing attacks where

hackers trick Web surfers into giving up personal

information like passwords and bank account data.

[irvin1130]

ei bm thanks sa message mo and it works fine ive restarted my wifes mb.

 

and 1 more thing ive read something in another forum about mac osx 10.6 snow leopard,any comment on this?

just got interested on the post thats why i asked

[boomouse]

ei bm thanks sa message mo and it works fine ive restarted my wifes mb.

 

and 1 more thing ive read something in another forum about mac osx 10.6 snow leopard,any comment on this?

just got interested on the post thats why i asked

 

1. You are welcome.

 

2. 10.6 will not outwardly have any new features relative to 10.5. All the changes will be underneath. Critics will say it is a cleaned-up version of 10.5 which has undergone several patches--not as much as any Windows OS but we are still at 10.5.4. On the other hand, I look forward to it cleaned-up version or new version because I am curious about how much more faster and reliable it will be as Apple claims.

 

3. I know that a few new things inside will be:

 

• Support for Ms Exchange Server--admittedly a better system for pushing information to your devices.
  
• True 64-bit memory support -- up to a theoretical 16 terabytes
  
• A an OS with a higher level of awareness of multi-core processors with OS hooks that will allow software developers to write their programs to be not just multi-core aware but multi-core efficient.
  
• Open CL, which is a language-based facility for software developers (note: I said developers, not programmers. Developers are people who design a program. Programmers are merely hired donkeys who are suppose to write the code to the specification of the designer) to be able to more directly address and control today's powerful GPUs.
  

My take on this? I'll try it out of course but I am even more excited by the kind of apps developers will come up with for an OS like this. A good OS will help spawn really impressive apps. That is the test.

[muttley]

I just learned the sad news that Ynzal is no longer an authorized Apple reseller.

 

Where else can I go for repairs and tech support? Thanks.